Qlogic QLA22xx board Installation Guide

Hardware Installation Guide for theQLA22xx Board FamilyFibre Channel Host Adapter Boards for the PCI BusFC0151103-00 EFebruary 6, 2001

What You Need for Installation 2 – Hardware Installation2-4 FC0151103-00 EFigure 2-4. QLA2204F Board LayoutISP CHIPSERIAL NUMBERISP CHIPISP CHIPJ1J2J

2 – Hardware Installation What You Need for InstallationFC0151103-00 E 2-5Figure 2-5. QLA2200G Board LayoutSERIAL NUMBERJ6ISP CHIPFigure 2-6. QLA2200

Power Distribution 2 – Hardware Installation2-6 FC0151103-00 E2.3Power DistributionThe QLA2200/2200L board supplies +5 volts to pin 7 of the HSSDC co

2 – Hardware Installation Installation in the ComputerFC0151103-00 E 2-74. Choose any PCI bus slot that supports bus mastering. Most motherboards aut

Installation Help 2 – Hardware Installation2-8 FC0151103-00 E10. Power up all external FC devices, then power up the PC and observe the monitor. The

FC0151103-00 E 3-1Section 3 Troubleshooting3.1Problems After InstallationThere are three basic types of installation problems that can cause yo

Fibre Channel Problem Checklist 3 – Troubleshooting3-2 FC0151103-00 E3.4Fibre Channel Problem Checklist Were all of the FC devices powered up before

FC0151103-00 E A-1Appendix A Fast!UTILNOTE: The Fast!Util BIOS utility does not run on Sun SPARC systems. Refer to the Software Installation Guide fo

Configuration Settings A – Fast!UTILA-2 FC0151103-00 EA.2.1Host Adapter SettingsFrom the Configuration Settings menu in Fast!UTIL, select Host Adapte

A – Fast!UTIL Configuration SettingsFC0151103-00 E A-3A.2.3Restore Default SettingsThe Restore Defaults option from the Configuration Settings menu r

QLogic CorporationPage ii FC0151103-00 EInformation furnished in this manual is believed to be accurate and reliable. However, QLogic Corporation ass

Configuration Settings A – Fast!UTILA-4 FC0151103-00 E Execution Throttle. This setting specifies the maximum number of commands executing on any on

A – Fast!UTIL Configuration SettingsFC0151103-00 E A-5 Disable Database Load. When enabled, the device database is read from the Registry during dri

Configuration Settings A – Fast!UTILA-6 FC0151103-00 E Extended Control Block. This setting enables all other extended firmware settings. The defaul

A – Fast!UTIL Scan Fibre Channel DevicesFC0151103-00 E A-7 Command Reference Number. This setting is reserved for Fibre Channel tape support, which

Select Host Adapter A – Fast!UTILA-8 FC0151103-00 E

FC0151103-00 E B-1Appendix BSpecifications Table B-1. QLA22xx Board Operating EnvironmentEnvironment Minimum MaximumOperating temperature 0°C/32°F 55

B – SpecificationsB-2 FC0151103-00 EConnectors QLA2200/2200L: HSSDC connector that supports copper cabling. Fibre optic support available using an ex

PC0151103-00-00 E Page iiiTable of ContentsSection 1 Introduction1.1 General Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table of Contents QLA22xx Hardware Installation GuidePage iv PC0151103-00-00 EFIGURESFigure Page2-1 QLA2200 Board Layout. . . . . . . . . . . . . . .

FC0151103-00 E 1-1Section 1 IntroductionNOTE: The following QLogic host adapter boards are collectively referred to as the QLA22xx board unless

What is Fibre Channel? 1 – Introduction1-2 FC0151103-00 Ethat support private loop direct attach (PLDA) and fabric loop attach (FLA). Installation of

FC0151103-00 E 2-1Section 2 Hardware Installation2.1Preinstallation ProceduresBefore installing your QLA22xx board, take a moment to read this g

What You Need for Installation 2 – Hardware Installation2-2 FC0151103-00 EQLA22xx board in the unlikely event that the NVRAM is corrupted. If the NVR

2 – Hardware Installation What You Need for InstallationFC0151103-00 E 2-3Figure 2-3. QLA2202F Board LayoutJ2ISP CHIPSERIAL NUMBERJ1ISP CHIP